- Welcome to Leaf Motor Bike.
Recent posts
#1
General Discussion / E-bike almost done, please hel...
Last post by leafmotor - Apr 24, 2024, 03:53 AME-bike almost done, please help with final issue: Throttle
Turn throttle. Hub motor Not work. No error code that display on S830 LCD.
Should check below:
1. There is a " 5 or 4 or 3 or 2 or 1 or 0" on the Left side of LCD.
* Be "0" – throttle NOT work. Should be 1 or 2 or 3 or 4 or 5
2. If please check brake lever if be ON. It's braking. "-O-"
3. Check P09 and P10
P09 should be 0
P09 = 0 (zero start) - When motor stops, turn throttle, works.
P09 = 1 (Non-zero start) - When throttle, not work. Should push wheel and let motor to turn first, then turn throttle, works.
P10 should be 2
P10 = 0 (ONLY PAS works, throttle Not work)
P10 = 1 (ONLY throttle works, PAS Not work)
P10 = 2 (PAS and throttle, both of them work)
Turn throttle. Hub motor Not work. No error code that display on S830 LCD.
Should check below:
1. There is a " 5 or 4 or 3 or 2 or 1 or 0" on the Left side of LCD.
* Be "0" – throttle NOT work. Should be 1 or 2 or 3 or 4 or 5
2. If please check brake lever if be ON. It's braking. "-O-"
3. Check P09 and P10
P09 should be 0
P09 = 0 (zero start) - When motor stops, turn throttle, works.
P09 = 1 (Non-zero start) - When throttle, not work. Should push wheel and let motor to turn first, then turn throttle, works.
P10 should be 2
P10 = 0 (ONLY PAS works, throttle Not work)
P10 = 1 (ONLY throttle works, PAS Not work)
P10 = 2 (PAS and throttle, both of them work)
#2
General Discussion / How to set LCD-003
Last post by leafmotor - Apr 23, 2024, 09:56 AMHow to set LCD-003?
Press "sw/middle button" from LCD more than 2 seconds,then LCD-003 will display.
Press "up & down button" together more than 2 sconds until 72 is flashing ( 72 is kmh, if you hope works 20mph / 32kmh, press "down" to be 32)
Press "sw/middle" button one time to save,then 26 is flashing.. (26 is wheel size. )
Press "sw/middle" button one time to save,then kmh or mph is flashing..
Press "sw/middle" button one time to save
Press "up & down button" together,set P
P1 = 46 (the number of magnets)
P2 = 0 (0 for low speed motor,1 for high speed motor)
P3 = 1
P4 = 0
P5 = 15 (48V battery is 15, 36V battery is 12, 24V battery is 9)
Press "sw/middle" button one time to save
Press "up & down button" together,set C
After setting,press "sw/middle" button more than 2 seconds until be back.
---------------
There is a " 5 or 4 or 3 or 2 or 1 or 0" on the Left side of LCD-003.
* Be "0" – throttle & pedal assist NOT work.
* Be "1" – throttle works (If install pedal assist, pedal about 3 circels,then can drive motor to work)
* Be "2" – throttle works (If install pedal assist, pedal about 2.5 circels,then can drive motor to work)
* Be "3" – throttle works (If install pedal assist, pedal about 2 circels,then can drive motor to work)
* Be "4" – throttle works (If install pedal assist, pedal about 1.5 circels,then can drive motor to work)
* Be "5" – throttle works (If install pedal assist, pedal about 1 circels,then can drive motor to work)
If NOT install that pedal assist,ONLY use throttle to drive hub motor. But Should be 1 or 2 or 3 or 4 or 5.(Be 0,turn off throttle)
Press "sw/middle button" from LCD more than 2 seconds,then LCD-003 will display.
Press "up & down button" together more than 2 sconds until 72 is flashing ( 72 is kmh, if you hope works 20mph / 32kmh, press "down" to be 32)
Press "sw/middle" button one time to save,then 26 is flashing.. (26 is wheel size. )
Press "sw/middle" button one time to save,then kmh or mph is flashing..
Press "sw/middle" button one time to save
Press "up & down button" together,set P
P1 = 46 (the number of magnets)
P2 = 0 (0 for low speed motor,1 for high speed motor)
P3 = 1
P4 = 0
P5 = 15 (48V battery is 15, 36V battery is 12, 24V battery is 9)
Press "sw/middle" button one time to save
Press "up & down button" together,set C
After setting,press "sw/middle" button more than 2 seconds until be back.
---------------
There is a " 5 or 4 or 3 or 2 or 1 or 0" on the Left side of LCD-003.
* Be "0" – throttle & pedal assist NOT work.
* Be "1" – throttle works (If install pedal assist, pedal about 3 circels,then can drive motor to work)
* Be "2" – throttle works (If install pedal assist, pedal about 2.5 circels,then can drive motor to work)
* Be "3" – throttle works (If install pedal assist, pedal about 2 circels,then can drive motor to work)
* Be "4" – throttle works (If install pedal assist, pedal about 1.5 circels,then can drive motor to work)
* Be "5" – throttle works (If install pedal assist, pedal about 1 circels,then can drive motor to work)
If NOT install that pedal assist,ONLY use throttle to drive hub motor. But Should be 1 or 2 or 3 or 4 or 5.(Be 0,turn off throttle)
#3
Hub Motor Drawing / 2000w single shaft motor drawi...
Last post by leafmotor - Apr 13, 2024, 10:20 AM2000w single shaft motor drawing
Main Features:
>. Engine: Single side shaft hub motor
>>. Voltage: 48V / 52V
>>. Power: 2000W
>>. Efficiency: 90.5%
>>. Max speed: 200RPM (can customize different speed version for free)
>>. Mechanical brake: Disk
>>. Cable location: shaft end
>>. Cable length:100cm / 40"
>>. Noise: < 60 db
>>. Surface: Black painted
More info about this single shaft motor
Main Features:
>. Engine: Single side shaft hub motor
>>. Voltage: 48V / 52V
>>. Power: 2000W
>>. Efficiency: 90.5%
>>. Max speed: 200RPM (can customize different speed version for free)
>>. Mechanical brake: Disk
>>. Cable location: shaft end
>>. Cable length:100cm / 40"
>>. Noise: < 60 db
>>. Surface: Black painted
More info about this single shaft motor
#4
Hub Motor Drawing / 1500w single shaft motor drawi...
Last post by leafmotor - Apr 13, 2024, 10:14 AM1500w single shaft motor drawing
Main Features:
>. Engine: Single side shaft hub motor
>>. Voltage: 48V / 52V
>>. Power: 1500W
>>. Efficiency: 90.5%
>>. Max speed: 200RPM
>>. Mechanical brake: Disk
>>. Cable location: shaft end
>>. Cable length:100cm / 40"
>>. Noise: < 60 db
>>. Surface: Black painted
More info about this single shaft motor
Main Features:
>. Engine: Single side shaft hub motor
>>. Voltage: 48V / 52V
>>. Power: 1500W
>>. Efficiency: 90.5%
>>. Max speed: 200RPM
>>. Mechanical brake: Disk
>>. Cable location: shaft end
>>. Cable length:100cm / 40"
>>. Noise: < 60 db
>>. Surface: Black painted
More info about this single shaft motor
#5
Bike Conversion Kit Video / Re: 29 inch hub motor - electr...
Last post by Peter Chou - Mar 11, 2024, 10:46 PM29 inch 48V 52V 1500W front freewheel hub motor bike conversion kit
With sine wave controller,brand new hub motor.. more info about this 29 inch bike motor kit
With sine wave controller,brand new hub motor.. more info about this 29 inch bike motor kit
#6
Bike Conversion Kit Wire Diagram / Re: 28 inch hub motor bike con...
Last post by leafmotor - Mar 11, 2024, 03:57 AM28 inch 60V 2000W front hub motor electric bike conversion kit wire diagram
Main Features:
>. Rim: 28 inch double wall Alloy (Rim Fit For: 28 × 1 1/2" tire)
>. Spoke: 12 gauge / 184mm Length × 36 pcs
>. Default: Silver spokes
>. Optional: Black spokes -- Please leave message.
>. Engine: Bldc hub motor
>>. Voltage: 60V
>>. Power: 2000W
>>. Efficiency: 90.5%
>>. Max speed: 50mph
More info about this 28 inch bike conversion kit
Main Features:
>. Rim: 28 inch double wall Alloy (Rim Fit For: 28 × 1 1/2" tire)
>. Spoke: 12 gauge / 184mm Length × 36 pcs
>. Default: Silver spokes
>. Optional: Black spokes -- Please leave message.
>. Engine: Bldc hub motor
>>. Voltage: 60V
>>. Power: 2000W
>>. Efficiency: 90.5%
>>. Max speed: 50mph
More info about this 28 inch bike conversion kit
#7
Bike Conversion Kit Wire Diagram / Re: 29 inch hub motor bike con...
Last post by leafmotor - Mar 11, 2024, 03:49 AM29 inch 60V 2000W front hub motor electric bike conversion kit wire diagram
Main Features:
>. Rim: 29 inch double wall Alloy (Rim Fit For: 29 × 1.95" ~ 2.5" tire)
>. Spoke: Black color 12 gauge / 189mm Length × 36 pcs
>. Default: Black spokes
>. Optional: Silver spokes -- Please leave message.
>. Engine: Bldc electric hub motor
>>. Voltage: 60V
>>. Power: 2000W
>>. Efficiency: 90.5%
>>. Max speed: 50mph
More info about this 29 inch bike conversion kit
Main Features:
>. Rim: 29 inch double wall Alloy (Rim Fit For: 29 × 1.95" ~ 2.5" tire)
>. Spoke: Black color 12 gauge / 189mm Length × 36 pcs
>. Default: Black spokes
>. Optional: Silver spokes -- Please leave message.
>. Engine: Bldc electric hub motor
>>. Voltage: 60V
>>. Power: 2000W
>>. Efficiency: 90.5%
>>. Max speed: 50mph
More info about this 29 inch bike conversion kit
#8
Hub Motor Drawing / 2000w beach snow fat bike moto...
Last post by leafmotor - Mar 10, 2024, 08:57 AM2000w beach snow fat bike motor drawing
170mm 2000w beach snow fat bike motor drawing
190mm 2000w beach snow fat bike motor drawing
Motor type: beach snow fat bike motor
Power: 2000W
Max efficiency: 90.5%
RPM: 680
Mechanical brake: V or Disc
Cable location: shaft end, Right
Cable length:150cm / 60" -- 5mm phase wires
Install: spacing of 170mm or 190mm fork
Noise: < 60 db
Surface: Black painted
Net weight: 8.85kg
Gross weight: 9.9 kg ( after packing )
More info about this 2000w beach snow fat bike motor
170mm 2000w beach snow fat bike motor drawing
190mm 2000w beach snow fat bike motor drawing
Motor type: beach snow fat bike motor
Power: 2000W
Max efficiency: 90.5%
RPM: 680
Mechanical brake: V or Disc
Cable location: shaft end, Right
Cable length:150cm / 60" -- 5mm phase wires
Install: spacing of 170mm or 190mm fork
Noise: < 60 db
Surface: Black painted
Net weight: 8.85kg
Gross weight: 9.9 kg ( after packing )
More info about this 2000w beach snow fat bike motor
#9
Hub Motor Drawing / 2000w electric motorcycle moto...
Last post by leafmotor - Mar 10, 2024, 06:29 AM2000w electric motorcycle motor drawing
170mm 2000w electric motorcycle motor drawing
190mm 2000w electric motorcycle motor drawing
Motor type: motorcycle motor
Voltage: 48V / 52V
Power: 2000W
Max efficiency: 90.5%
RPM: 680
Mechanical brake: V or Disc
Cable location: shaft end, Right
Cable length:150cm / 60" -- 5mm phase wires
Install: spacing of 170mm or 190mm fork
Noise: < 60 db
Surface: Black painted
Net weight: 8.85kg
Gross weight: 9.9 kg ( after packing )
More info about this 2000w electric motorcycle motor
170mm 2000w electric motorcycle motor drawing
190mm 2000w electric motorcycle motor drawing
Motor type: motorcycle motor
Voltage: 48V / 52V
Power: 2000W
Max efficiency: 90.5%
RPM: 680
Mechanical brake: V or Disc
Cable location: shaft end, Right
Cable length:150cm / 60" -- 5mm phase wires
Install: spacing of 170mm or 190mm fork
Noise: < 60 db
Surface: Black painted
Net weight: 8.85kg
Gross weight: 9.9 kg ( after packing )
More info about this 2000w electric motorcycle motor
#10
Hub Motor Drawing / 1000w electric motorcycle moto...
Last post by leafmotor - Mar 10, 2024, 05:50 AM48V 52V 1000W rear electric motorcycle motor
1000w 170mm dropout electric motorcycle motor
1000w 190mm dropout electric motorcycle motor
Detail:
Motor type: motorcycle motor
Voltage: 48V / 52V
Power: 1000W
Max efficiency: 90.5%
RPM: 680 (Free customize other speeds)
Mechanical brake: Disk
Cable location: shaft end, Right
Cable length:100cm / 40
Install: spacing of 170mm or 190mm fork
More info about this 1000w electric motorcycle motor
1000w 170mm dropout electric motorcycle motor
1000w 190mm dropout electric motorcycle motor
Detail:
Motor type: motorcycle motor
Voltage: 48V / 52V
Power: 1000W
Max efficiency: 90.5%
RPM: 680 (Free customize other speeds)
Mechanical brake: Disk
Cable location: shaft end, Right
Cable length:100cm / 40
Install: spacing of 170mm or 190mm fork
More info about this 1000w electric motorcycle motor