Category Archives: BLDC motor - Page 3

leaf bike 26 inch 48V 1500W rear hub motor wheel kit

Posted by on March 15, 2025 Comments Off on leaf bike 26 inch 48V 1500W rear hub motor wheel kit

Q: I am interested to buy a complete Rear 1500w hub motor wheel ( the latest model with upgraded phase wires, 0.35mm lamination etc).
The model model I think is LBM26481500RN and I would like to know the following before if buy:
– the no load rpm for 4T, 5T and 6T motor at 48v
– and the top speeds under load for 26 inch wheel.
I am looking to have a maximum 55 – 60kph (not less than 55 ) top speed under load but a bit more torque for off road riding.
Also for a electric bike motor with disc brake mount, cassette, temperature sensor and a rim that fits a 2.5 tire is the same price?

A: If not load, 4T 1500w 26 inch hub motor is about 72kmh (work at 48v)
If not load, 26 inch 1500w 5T is about 60kmh (work at 48v)
We can make cassette case motor with 2mm phase wire. But we still recommend standard version with thread screw with 2.5mm phase wire.
Also,standard version is easy to install than cassette case..
* With disc brake mount, cassette,temp,rim fit for 2.5 tire – The same price.
We recommend: with disc brake, standard version (No cassette version),temp,rim fit for 2.5 tire.

Q: can you please send me a more precise data (numbers) about the rpm @ 48V for each available wingdings available, like a performance table or similar?
I found on internet different available information for this motor, but their are not consistent, there are also the forums..and each data is different.
I was hopping that you can provide me more figures..
And also,I don’t understand why for the cassette hub the phase wires are 2mm while there are existing on the opposite side ?

A:Thank you so much for the clear explanations, I understood very well now what are the draw backs for each design.
Also, I was looking over the performance datasheet and I suppose that those parameters are for the 4 turn winding I suppose right?
So for the 5T the maximum rpm with be lower and torque a bit higher. Also the max efficiency point will be at a lower rpm.
Good, so if I want to place an order for a 5T 1500W 26 inch Rear hub motor kit wheel with the following requirements:
disc mount
threaded sprocket
temp sensor
135 mm drop out
26 inch Rim for 2.5 tire (23-25 mm wide rim)
12 gauge spokes

A: Yes. That 4 turn winding.
If 5T, the max rpm with be lower and torque a bit higher.
26 inch wheel, we recommend 5T
Standard rear 1500w 5T with the following requirements
* can install disk the left side of motor
* can install threaded sprocket on the right side of motor
* with temp
* fit for 135mm dropout
* We have 26 inch out.size 25mm or out.size 32mm wide rim (Our 32mm rim is fit for 26 inch)
Please click below sites.
I think 26 inch all black color rim is fit for your 2.5 tire.

hub motor controller working principle

Posted by on March 15, 2025 Comments Off on hub motor controller working principle

hub motor  controller electronic reversing device, instead of the traditional mechanical commutation device (commutator and brush), not only retained the DC motor speed control with good starting characteristics, and AC motor with simple structure and easy maintenance This motor in good, reliable, therefore, the rapid development in recent years. Traditional DC motor armature is rotated, the pole is stationary, but bldc motor driver in this contrast, the magnetic pole is rotated, the armature is stationary, the armature winding current commutation can make use of position sensors and electronic switching circuit to complete. Brushless motor. hub motor driver generally motors, position sensors, and electronic switch consists of three parts. Motor itself consists of multi-phase (three phase, four-phase, five-phase range) armature windings on the stator pole and a certain number of permanent magnet rotor component. AA, BB, CC, said three-phase motor stator windings, NS is a permanent magnet, the motor rotor, PS is the rotor position sensor, and its coaxial rotor and motor rotor is connected, BG1, BG2, BG3 electronic switching circuits power switch, three-phase windings A, B, C respectively, BG1, BG2, BG3 in series to the power supply after. Its operation principle is that a signal controlled by the PS BG1, BG2, BG3 and other switch on on and off, when the switch turns on, the corresponding stator windings, there is current and magnetic field through the magnetic field and permanent magnetic interaction between the rotor pole will generate torque, the motor rotor, the motor coaxial with the rotor position sensor is connected, it also followed the rotation of the rotor and in turn to BG1, BG2, BG3 signal to control the turn on and off, to the armature winding current with the rotor position changes according to the order of commutation, the magnetic armature rotary stepper motor’s rotor to rotate continuously go on.

about 1000w and 1500w electric hub motor

Posted by on March 15, 2025 Comments Off on about 1000w and 1500w electric hub motor

I am part of a team what will be competing in an ECO marathon challenge. That means we will be building a vehicle that will compete with other teams. The most efficient vehicle will win the prize!

We are building a three wheeled car, driven with a hub motor used as mid-drive motor. I have been a member of the Endless-Sphere group for very long and knew that the Leaf 1500Watt hub motor is the best in therm of efficiency.

So my question is, is it possible to get the hub motor for a cheaper price (free shipping) in exchange for some stickers we will put on our vehicle? Let me know if you have any interest in sponsoring our build/team! If you have any questions feel free to email me back, I will get back at you as soon as possible!

Could you tell us what winding options are available for the 1000Watt electric bike motor (Item ID #LBM481KRNC) and the 1500Watt electric bike motor (Item ID #LBM481500RNC).
We are looking to find out what hub motor is the most efficient on a voltage of 48Volts.

So could you tell us the max RPM, per winding option (1000watt and 1500watt) at 48Volt?

We would like to compare each different electric bike motor(1000/1500watt and different winding options) in a simulator.
The simulator we are using to compare each hub motor is an online simulator

To simulate all the different electric bike motor options and windings we need some parameters from each motor 1000watt and the 1500watt. Is it possible to provide us these motor parameters, so we can run a simulation on the 1000watt motor with different windings and on the 1500watt with different windings?

What would be the max RPM of a hub motor with those options (20 inch 1000w cassette and disk brake)?
And what would be the turn count?
Thickness of laminations? Will it have the same efficiency as the 4Turn 1000watt motor?

29 inch electric hub motor kit have problems with the cassette

Posted by on March 13, 2025 Comments Off on 29 inch electric hub motor kit have problems with the cassette

I ordered the 48v 1500W electric bike kit, with cassette.
I have problems with the cassette, the cassette is wider than where the dropouts sit around the axle.
So the hub motor wheel with the cassette on is wider than 135mm.
My bike frame is 135mm, and the website said it would fit on a 135mm frame.
When the cassette is on the hub motor wheel and i put the electric bike motor wheel on the bike, the frame grinds against the cassette when I tighten the electric bike motor wheel.
I have made it work using spacers so it spins freely, but the wheel is offset to one side now and i think my frame is spread wider. It is an aluminium frame.
Also the website said max 7 speed gear, but the cassette is for a 9 speed gear, which is also mounted now, is it suppose to be able to take a 9 speed gear, or is that an accident?
Any advice on what to do?
Also, any advice on mounting the torque arms? My frame is aluminium.

Steel is okay.But Aluminium is not good to make it larger. We worry if make aluminium frame to larger will break frame.
We recommend use 7 speed or 6 speed or single speed..

You will receive below goods:
1x pcs of 29 inch 48v 1500w rear hub motor wheel (black spokes, cassette)
1x pcs of 48V bldc motor controller (New version LCD controller)
1x pcs of LCD (New version LCD-003)
1x set of twist throttle
1x set of brake levers
1x pcs of three button switches ( use to control cruise,reverse..)
1x set of pedal assit ( It’s fit for European,if you don’t use,ONLY use throttle is okay )
Some spare spokes with plugs

——————————————-
How to set max speed?
If you feel motor is too fast,please set it to be low speed.
* Press “sw/middle button” from LCD more than 2 seconds,then LCD will display.
* Press “up & down button” together more than 2 sconds until 72 is flashing ( 72 is kmh, if you hope works 20mph / 32kmh, press “down” to be 32)
* Press “sw/middle” button one time to save,then 29 is flashing.. (29 is wheel size. Don’t set)
* Press “sw/middle” button one time to save,then kmh or mph is flashing..
* Press “sw/middle” button one time to save,then press “sw/middle” button more than 2 seconds until be back.

I would like to order a rear 48v 1500w hub motor wheel

Posted by on March 13, 2025 Comments Off on I would like to order a rear 48v 1500w hub motor wheel

I really like (love) your hub motors (they perform really well and last a long time) and now I have the time to get the one I always needed.
And here is a very similar bike which also has a 1000W option rear hub motor this one has multiple speeds, most probably 7.
I have asked the rear dropout widths. Will get back to you as soon as I know. And I have a steel frame with a 145mm dropout now which I can widen. I do not 100% understand the trade offs that you are referring to when you say that the rim doesn’t matter, it is the 3 inch tire that is the issue for this hub motor as the same electric bike motor would also go into a wider dropout fat bike which also has an even wider tire – 4 inches. I need more details to understand it more clearly.
And there are other options at the front end of the chain where we can move the chain out a bit:

1. the little chain guide can help – this is mounted to the seat tube to push out the chain from the frame and tire
2. move bottom bracket out to the right
3. or get a bottom bracket with a longer spindle
4. or add spacers between the crank and chaining

What hub motor do you use for your 2000w and higher power fat bike applications? What would I need to change to make any motor work?

I see that the 2000w electric bike motor is 74mm wide which is only 4 mm wider than the 1500w hub motor. I have attached some new pics of my bike from different angles so that you can see how much clearance I have and if I just go with a single speed setup, I will have enough clearance for the chain but in case I need to get additional clearance, I do have some options mentioned previously. So my question now is would a wider or higher power motor work better? I see that the 1500w motor works with dropouts of between 135 and 155mm. And then the 2000w one begins at 170mm. I can widen my dropout and since I won’t be needing the space of a 7 speed cassette, I should be able to have the chain clearance I need.

The basic principles of the permanent magnet hub motor

Posted by on March 12, 2025 Comments Off on The basic principles of the permanent magnet hub motor

We talk about one type of permanent magnet hub motor for electric bike. It’s a hub electric bike motor, sometimes we also call it brushless dc hub motor .

The permanent magnet hub motor and the hub motor driver is a typical product for e-bike recently.

Generally the electric bike motor ’s rotor winding is made of a three phase star connection, with the three-phase asynchronous AC hub motor is very similar. The hub motor rotor has been magnetized permanent magnet, in order to detect the polarity of the hub motor, there are three halls sensors on the rotor.

The hub motor driver is made by the power electronic devices and integrated circuits, its function is to receive electric bike motor ’s start, stop and brake signal so that control the hub motor to start, stop and brake; receive the position sensor signals and reversing signal, used to control the inverse power tube change the bridge off to produce a continuous torque; receive the speed command and speed feedback signal used to control and adjust the speed; provide protection and display

The main circuit is a typical voltage-type AC – DC – AC circuit, other pieces of alternating square wave frequency of 5-26KHZ modulation wave symmetry.

Permanent magnet NS alternating exchange, the position sensor phase difference of 120 ° U, V, W, square wave, combined with the six-state encoding signal forward / reverse signal generator: 101,100,110,010,011,001, through processing logic components to produce conduction of T1-T4, T1-T6 turns on, the T3-T6 conduction, T3-T2 turn-on, turn-T5-T2, T5,-T4 conduction, which means that the DC bus voltage is incremented A + B-, A + C-, B + C-, B + A-, C + A-, C + B-, so that the rotor turned a pair of NS pole, T1-T6 power tube fixed into six states followed by conduction. Each state, only two phase winding are energized in order to change a state, the axis of the magnetic field generated by the rotor winding 60 ° electrical angle of rotation in space, the rotor follows the rotor magnetic field rotation is equivalent to the space of 60 ° electrical angle position, the rotor in a new location so the position sensor U, V, W to produce a new set of coding according to the agreement, the new coding and changed the power tube combination of conduction, the magnetic field generated by the rotor winding shaft forward 60 ° electrical angle, and so on, permanent magnet electric bike motor produces continuous torque, drag the load for a continuous rotation. Permanent magnet DC motor commutation is itself, rather than forced by the commutation, also known as controlled synchronous hub motor.

Hub motor, electric bike motor supplier: Leaf Motor Technology Co.,Ltd

bldc motor interaction principle

Posted by on March 12, 2025 Comments Off on bldc motor interaction principle

Based on the principle of rotation of the motor for the Fleming left hand rule, when a wire placed in a magnetic field, if the current through the wire, the wire will cut the wires generate the magnetic field lines move. Current into the coil creates a magnetic field using the current magnetic effect, the solenoid magnet at a fixed continuously rotating device that can convert electrical energy into mechanical energy. And a permanent magnet or by another group of the magnetic field generated by the coil to generate power bldc motor interaction principle is the stator does not move, the force generated by interaction of the rotor according to the direction of movement. bldc motor controller is on the alternating current through the stator windings, a rotating magnetic field, rotating magnetic field attracts the rotor rotates bldc motor with the basic structure include “armature”, “field magnet,” “slip ring”, “brush” . Armature: You can rotate around the axis of the soft iron core wound multi-turn coil. Field magnet: the strong magnetic field of permanent magnet or an electromagnet. Collector ring: coil about two to two semi-circular termination of slip ring, with the coil rotation for changing the current direction of the change to the device. Each half-circle rotation (180 degrees), the coil current to change direction once. Brushes: carbon usually made of slip ring brush contact with a fixed location to be connected to power.

Electric hub motor bike conversion kit for electric bike

Posted by on March 10, 2025 Comments Off on Electric hub motor bike conversion kit for electric bike

Ride a bike everyday is good for health. It can help you lose weight and achieve healthier body. By the way,sometimes riding for a long trip or steep road that is too tired.Buy a new e-bike is too expensive.Why not place an order for bike conversion kit and convert your common bike to electric bike by yourself.

Standard bike conversion kit includes:
1.hub motor wheel (8″ 10″ 12″ 14″ 16″ 18″ 20″ 24″ 26″ 27.5″ 700c 28″ 29″ 27″)
2.motor controller(drive hub motor)
3.twist throttle or thumb throttle(default twist throttle)
4.brake lever with low voltage to brake
5.three-button switches(control horn,led lights,cruise..)
6.pas(for Europe)
7.battery with charger(optional)

1 set of bike conversion kit has three key products:hub motor,motor controller and electric bike battery.
Hub Motor:There are 8″ 10″ 12″ 14″ 16″ 18″ 20″ 24″ 26″ 27.5″ 700c 28″ 29″ 27″ hub motor,what inch would you choose depend on your common bike wheel size.Motor type:brushed hub motor or brushless hub motor also called BLDC hub motor.Now because the bldc hub motor has advantage of low noise,high efficiency that replace of brushed hub motor.
Leaf Motor has 36V 750W / 48V 1000W brushless gearless electric bike motors are popular with North America.The other 24V 250W / 36V 250W bldc geared hub motors,European prefer them.

Motor Controller:Bldc motor controller which is called a heart of bike conversion kit system.Generally 6-MOSFET controller drives 250W hub motor,9-MOSFET drives 500W,12-MOSFET drives 1000W bldc motor.
Leafmotor is selling a LCD motor controller that display speed,mileage,battery gauge.

Battery:In China,electric bikes still use lead-acid batteries,they’re much cheaper,but a little heavy.North America or Europe always use lithium batteries that are more environmental.
Leafmotor has three types of lithium batteries:high speed,frog and bottle electric bike batteries for customers to choose.We found most of issues from lithium batteries that were not used correctly.
Three are two advice about how to use lithium battery.
1.Please remove power connector. If you don’t ride your e-bike for a couple of days.
2.Charge your battery often,but please don’t overcharge it.

Received your bike conversion kit,please check packing box first,then disconnect it and check each product that make sure all goods are okay.Then prepare below tools to install bike kit.
1.open-end wrench(loose/tight screw nuts)
2.philips screwdriver(fix LCD)
3.some zip ties(fix wires)

Remove the front or rear wheel.Find out the motor’s direction of rotation.Fix this motorized hub motor wheel to your frame fork and use open-end wrench to tight both screw nuts.According as install instruction manual and wiring diagram to connect wires make sure your wheel in the air,power on your battery,test bike conversion kit system.Turn throttle,if motor works well without any noise.Then use zip ties to fix wires.If not,please re-check your wire connecting.

If everything is good,it will take about 10 minutes to done it.Just order 1 set of electric hub motor bike conversion kit,your common bike will become electric bike.Cost less,get more.Have you found some fun?

Hub motor,bldc motor,bike conversion kit supplier: Leaf Motor Technology Co.,Ltd.

Hub motor kit ceased to function

Posted by on March 8, 2025 Comments Off on Hub motor kit ceased to function

On February 8th we ordered your 26″ 48V 1000W front electric bike kit(1 set of 26” 48 1000W hub motor wheel with lcd bldc motor controller,twist throttle,brake levers,48V lithium battery) which was delivered to us on February 13th.Shipment is very fast.But the packing box is broken,we disconnect it and found the left brake lever was defective and I e-mailed you about getting a replacement set of levers. You told me that the parts would be sent. They never were received. I disconnected the lever plugs and have been using the bike for the past 1 month without them being hooked up.

Last week the bike ceased to function. I have 50+ volts going to the bldc motor controller connection but when I plug in the hub motor controller, the voltage drops to 1.8V and nothing happens. When I disconnect the hub motor connection, the voltage remains at 1.8V. As soon as I disconnect the battery, the electric bike battery shows full voltage of 50+ volts. The voltage indicator lights do not light up at all. So I have good voltage going to the controller but nothing works. I disassembled the controller to see if there was a broken connection or burned out part but can find nothing visibly wrong – when I connect a tester to the board the voltage shows 1.8 when should be 50 at the input connection. Something is wrong internally and I now need the hub motor controller to be replaced. I am relying on the electric bike kit to get to and from work so time is very important to me.

Please send me a new hub motor controller as soon as possible. Also send me the previously promised brake lever set replacement at the same time (as long as it does not slow down the shipment of the hub motor controller). I would also appreciate it.

Hub motor,bldc motor,electric bike kit supplier: Leaf Motor Technology Co.,Ltd

LCD bldc motor controller for e-bike

Posted by on March 8, 2025 Comments Off on LCD bldc motor controller for e-bike

There are two types of hub motor wheels are used for e-bikes. One type is hub bldc motor , the other is brushed hub motor. Because the brushed motor had some disadvantage of high noise, shorter-use life, low efficiency..

These days hub bldc motor wheels are used for electric bikes widely and had replaced brushed hub motor.

So more and more motor controller are showed in market. For example: cruise brushless controller , regen brushless controller, programmable brushless controller, lcd bldc motor controller…

Convert a bike to an e-bike, we should choose a hub bldc motor wheel with brushless controller and throttle, brake lever,on/off switches,disk brake,front&rear lights,horn..etc accessories

European like 250w hub bldc motor and North America prefer 750w / 1000w bldc motor. How to purchase a good brushless controller to drive this bldc motor .

Generally 250w bldc motor need to be driven by 6-MOSFET brushless controller, and a 9-MOSFET motor controller dirves a 750w bldc motor,a 12-MOSFET brushless controller dirves a 1000w bldc motor.

Now nearly all types of brushless controller for e-bikes have cruise, alert, reverse, limited speed..etc. function.

If you buy 1 set 48V DIY kit, you had better to choose 48V 12-MOSFET/15-MOSFET brushless controller. Please don’t order 9-MOSFET motor controller to drive your 1000W brushless controller, it’s the heart of e-bike. 1000W bldc motor will bring larger current and high temperature, 9-MOSFET can’t afford.

For the bulk .of motor controller, larger, better. Larger bulk has better cool system.

In past, there was a guy sold regen motor controller, but nearly all sold regen controllers were broken in 30 days. Because when you brake, this regen controller will bring twice current to stop your e-bike, thus larger current would break MOSFET directly.

Now programmable controller is still showed in market. This brushless controller seem has nice face, but its head is small, can’t stuff more MOSFET. Use this brushless controller to drive 750w / 1000w bike system and break this nice face controller is normal. Don’t be arrest by programmable. You will find nothing for actual use when you use.

We have LCD cruise controller, more MOSFET, don’t worry your motor controller will be broken.
LCD bldc motor brushless controller for e-bike.

Bldc motor, motor controller , brushless controller supplier: Leaf Motor Technology Co.,Ltd