Category Archives: electric bicycle - Page 2

26 inch electric hub motor kit for the dropout 160mm fork

Posted by on December 30, 2021 Comments Off on 26 inch electric hub motor kit for the dropout 160mm fork

Q: Are you able to supply a rear hub motor kit wheel (36v @ 500W – 750w) for a rear dropout of 160mm?
I have an existing e-bike that uses a 250w geared rear hub drive on a 26 x 1.95 wheel.
It has a 7 speed gear, standard 160mm disk brake and a bike mount (frame) width of 160mm.
I would be happy to go from a geared (small hub) to the larger electric bike motor kit type.
The existing bike frame is steel (not carbon or an alloy) so I may be able to ‘bend’ the rear forks… (fit).
I have included a PDF diagram (attached) to show the existing rear hub motor fitting size.

A: Yes, we have dropout of 160mm 36V 750W electric bike motor.

Q: With the new Leaf controller and LCD, I know I can limit the maximum output speed of the 750w Direct Drive hub motor to a set (safe) maximum speed for each PAS mode 1 – 5.
With our Australian laws, I want to honor speed and safety – yet have a safe speed and torque (reserved) for hills.
I respect that you have kindly supplied my order with a 320RPM hub motor ( a good choice).
My question is: “Does the max speed by set by LCD / Controller economically limit the maximum current sent to the hub motor”?
I am talking here about battery life with a low speed LCD / Controller setting ‘modulating’ the full power sent to the hub motor.
So if I program the setting to say 25Km/h, then is the torque output effected at speeds less than the given 25Km/h?

A: Yes, if you set max 25kmh by LCD, motor will work less than 25kmh.(You can set max 10kmh,11kmh,12kmh….48kmh,49kmh,50kmh)

1.Press “SW” from LCD. Turn on LCD
2.Press “up” &”down” together for more than 2 seconds in 3 seconds after LCD display – Then “72” will flash.
3.Press “down” or “up” to set any max speed. Press “SW” one time to save. Then “26” will flash. It’s tire size. Don’t set. Still press “SW” one time to save. Then “kmh / mph” will flash. Don’t set. Press “SW” one time to save.
4.At last, press “SW” more than 2 seconds, then will be back.

There is a Three button switch inside parcel.

** Black switch (be Left side / Middle – motor works forward. Be right side, motor works backward/reverse)
** Red switch (Be left side / regen off. Be right side / regen on)
** Green switch ( When motor is working, press this green switch one time. LCD is display C, motor will work as the same speed) – Re-press this green switch one time, or press brake lever, turn throttle to max, motor will stop.

Leaf 26 inch 48V 1000W rear hub motor – bike conversion kit

Posted by on December 30, 2021 Comments Off on Leaf 26 inch 48V 1000W rear hub motor – bike conversion kit

* The conversion 26 inch hub motor kit combines the full E-bike technology: direct drive Brushless Gearless high torque 26 inch hub Motor to change almost every bicycle into a personal electric bike. Save energy, protect environment and save money with a lot of fun.
* Saving 10% of electricity, Improve the efficiency of 8% With The Newest Materials Steel Rotor.

Main Features:
>. Rim: 26 / 559 double wall Alloy ( tire: 26 × 1.5″ / 1.75″ / 1.95″ / 2.1″ / 2.5″)
If the width of your tire / tyre is 2.1, 2.2, 2.3, 2.5, 3.0…(bigger than 1.95 inch)
Please note tire/tyre size when you place an order so that we can send a wider rim & fit for your wider tire/tyre.
>. Spoke: 12 gauge / 156mm Length × 36 pcs

>. Engine: Bldc hub motor
>>. Voltage: 48V
>>. Power: 1000W
>>. Efficiency: 90.5%
>>. Max speed: 71 kmh — 45mph Default (Optional other speed: 35mph or 25mph,15mph…)
>>. Mechanical brake: Disk or V
>>. Freewheel / Cassette: space for 6 or 7 gears
Default: install screw thread Sprocket (If install Cassette Sprocket,please leave message)
>>. Cable location: shaft end , LEFT
>>. Cable length:100cm / 40″
>>. Install: spacing of 135mm fork
>>. Noise: < 60 db >>. Surface: Black painted

>. Driver: brushless controller
>>. MOSFET: 12 PCS
>>. With LCD: YES
>>. Rated Voltage: DC 48 Volts
>>. Min. Voltage: DC 40 ± 0.5 V
>>. Rated power: 1000 Watts
>>. Casing material: aluminium
>>. Maximum Current: 26 A ± 1 Amps
>>. Thermal: aluminum shell and the substrate
>>. 3 phase 120° brushless motor
>>. Operating Conditions: -20~45 °C
>>. Waterproof design
>>. Size: 171 mm L × 82 mm W × 42 mm H

Updated LCD , More Function:
* Cruise — Green switch control it
* Forward & Rackward (Optional) — Black switch control it
* Regen brake — Red switch control it
* Kmh & mph (Optional)
* Set Max speed ( 0 ~ 72 kmh / 45 mph )
* Pedal assist ( 1 – 5 )
* Temperature
* Motor power
* Timer
* Battery gauge
* …

Package Content:
1 x 26 inch Newest 48V 1000W rear hub motor wheel
1 x 48V 1000W 12-MOSFET motor controller
1 x LCD – 003 ( display speed, mileage, battery gauge.. )
1 x Twist throttle — Cable length: 1500mm
1 x Brake levers — Cable length: 1500mm
1 x Three button switches ( control cruise, regen brake, reverse .. ) — Cable length: 1500mm
1 x Pedal assist — Cable length: 1500mm

Net Weight: 24.5 lbs
Package Size: 60cm L × 25cm W × 60cm H / 23.6″ L x 9.8″ W x 23.6″ H
Package Type: Cardboard Box

If the width of your tire / tyre is 2.1, 2.2, 2.3, 2.5, 3.0 inch…(bigger than 1.95 inch)
Please note tire/tyre size when you place an order so that we can send a wider rim & fit for your wider tire/tyre.

26 inch 48V 1500W bike conversion kit info request

Posted by on December 30, 2021 Comments Off on 26 inch 48V 1500W bike conversion kit info request

Q: I was contacting you in hopes of getting some more information about a conversion 26 inch kit that you offer on your leaf bike website. I’m interested in the Item:LBCK26481500FN and Item:LBCK26481500RN, my question is do you offer the 26 inch 48v 1500w bike conversion kit with both the front and rear 26 inch hub with rims instead of having to purchase both kits, basically a one sole complete kit. I was hoping that 48V 20Ah lithium battery would be compatible with the kit as well. Please contact me when available. Thank you for your time and assistance.

A: Yes,can use LBCK26481500FN and LBCK26481500RN on one bike.
Need below parts:
* 1 set of throttle — use to drive two controllers
* 1 set of brake lever — use to drive two controllers
* 1 set of switch — use to control cruise
* 1 set of LCD — — use to drive two controllers
* 2 sets of 48V 1500W brushless controller
* 1 pcs of front 48V 1500W 26 inch hub motor
* 1 pcs of rear 48V 1500W 26 inch hub motor
* 1 set of lithium battery — — use to drive two controllers

Install 48V 1500W rear 26 inch bike motor on rear fork and 26 inch front hub motor wheel on your front fork.Fix controller,install throttle,brake lever,switch,LCD,also these parts all have two plugs for both controllers.Then connect rear 26 inch hub motor wheel to one controller.The other front 26 inch hub motor wheel to the other motor controller.Use 48V 20ah lithium battery to drive these two controllers. Power on and Press “sw” from LCD more than 2 seconds,then LCD will display. Turn throttle,electric bike works.

leaf 20 inch 48V 1500W rear hub motor – bike conversion kit

Posted by on December 30, 2021 Comments Off on leaf 20 inch 48V 1500W rear hub motor – bike conversion kit

Q: Regarding: Newest 20 inch 48V 1500W rear hub motor – bike conversion kit works on any bike.

What is the max current of the hub motor controller at 48V?
Is the controller programmable to other max current settings?
Does the LCD display show power either in watts, or volts and amps?

A: It’s max 40A
This bike motor controller can set other max speed.
Yes,LCD display power

Q: If I order just the hub motor, can the 1500W rear hub motor have a 10K NTC thermistor installed in it?

A: This 1500w hub motor with 10k themistor (It’s default)

Q: I have a 135mm fork. Can the Shimano Freewheel, 7 Speed, 14-28T be installed on the hub motor and still fit within 135mm?

A: Shimano 7 speed screw-on sporket can be install this hub motor.(TZ-21) – It’s default. Also,fit for 135mm fork.
If other shimano 7 speed cassette sprocket,need to modify hub motor.(We still can make.)

Q: Thanks. Do you sell a Shimano sprocket with an 11 Tooth (11T) that would fit the 1500W rear hub motor?
Q: Can you list the description of each wire in the hall/temperature connector pictured below?
red – ?
black – ?
yellow – ?
white – ?
green – ?
blue – ?

A: Red +
Black –
Yellow – W
White – Temp
Green – V
Blue — U

Q: What parts is includes on this 20 inch 48V 1500W rear bike motor kit?

Package Content:
1 x 20 inch Newest 48V 1500W rear hub motor wheel
1 x 48V 1500W 12-MOSFET motor controller
1 x LCD ( display speed, mileage, battery gauge.. )
1 x Twist throttle — Cable length: 1500mm
1 x Brake levers — Cable length: 1500mm
1 x Three button switches ( control cruise, regen brake, reverse .. ) — Cable length: 1500mm
1 x Pedal assist — Cable length: 1500mm

Net Weight: 11.0 kg / 24.2 lbs
Package Size: 50cm L x 23cm W x

50cm H / 19.7″ L x 8.7″ W x 19.7″ H
Package Type: Cardboard Box

1500w hub motor rpm

Posted by on December 30, 2021 Comments Off on 1500w hub motor rpm

I have done a little more testing with the 1500w hub motor. I think that I am
happy with the current winding. I am giving the motor 65A battery, 180
amps phase.. and it is like a rocket now.
The efficiency is very good.. the most efficient hub motor I have
tested.. good work!

But I want to be sure about the winding for my post about your 48V 1500W bike motor,
because your webpage shows lots of different RPM for the same motor (
this is confusing )..

If someone orders the hub motor from your website.. they will receive a 16*4
turn motor, which is 650rpm @ 49v = 13.26 kV
And the 13*5 turn motor would do 550rpm @ 49v = 11.2 kV
Is this correct…?

P.S. If you are interested in having a hub motor re-seller.. I told someone
in the USA about your hub motors and told him about my tests.

I got the hub motor and have tested it. It’s a great hub motor, but the winding is too fast for a 26 inch,650B,700C,28 inch,29 inch hub motor wheel.It’s better for 14 inch,16 inch,18 inch,20 inch,24 inch bike motor wheel.

The no load speed on the hub motor I received = 640rpm on 49v.

I notice on your web page that you sell stator windings.. I was wondering
how many turns this hub motor has.

Is it possible that you could sell me a stator winding with one more turn that could do 500-550rpm on 49v?

16 * 4T 650RPM
13 * 5T 550RPM
11 * 6T 450RPM
9 * 7T 350RPM
8 * 8T 250RPM
7 * 9T 150RPM
…………

18 inch gearless brushless hub motor for electric bike

Posted by on December 30, 2021 Comments Off on 18 inch gearless brushless hub motor for electric bike

I am interested in the 18 inch rear gearless bldc hub motor provided by leaf bike company and I had a few questions about the hub motor.

1) What is the rated torque?
2) What is the maximum torque?
3) How many poles are there in this hub motor?
4) Does it contain any brakes? If so, what type? (Disc/Drum/V-brake)
5) Does it contain hall sensors? If so, How many and what is their description?
6) Most importantly, is this motor a brushless dc motor (BLDC) or a permanent magnet synchronous motor(PMSM)? This greatly affects my choice, as both types are sometimes very close to each other, so I needed verification on what type it was.
7) Does it have a waterproof gradient?
8) Dimensions: I had an issue with the dimensions listed in the description compared to dimensions in the drawing for the motor on Leaf Motor site. I am actually looking for a motor that is around 16 inches, however, I chose the 18 inches because the image for the 18 inches shows the diameter being 372 mm which is equal to around 14.6 inches, which isn’t 16 inches but is very close. The diameter of the electric bike motor is crucial for my wheel choices and so clarifying what the actual diameter of this motor would be very helpful, I can’t risk not being sure of the dimensions as I am currently designing the vehicle and need to be very accurate, and that’s why a professional mechanic is needed specialized in this kind of vehicle, because sometimes people think a person who’s good with cars will be good at bikes too.
9)Does this motor support regenerative braking?
10) What is the back EMF of this motor?
Finally, I would like to apologize if these are too many questions but I am in need of the maximum clarifications I can get to be as precise, so any information you can provide will help me on my quest to find the best. I will be forever grateful for your help.

A:
Please click our new site.
https://www.leafbike.com/products/e-scooter-hub-motor/18-inch-electric-motor/
There is more drawing & performance.

* This 18 inch is fit for 18 * 2.125 or 2.5 tire.
The dia. of this 18 inch is 372mm, it’s fit for 18 inch bike tire.

* 46 pcs magnet, with 3 pcs hall sensor… It’s brushless motor.

I want to purchase one of leaf hub motor kits

Posted by on December 30, 2021 Comments Off on I want to purchase one of leaf hub motor kits

I have done a lot of research and leaf motor and services keep coming up as a fine choice.

My original choice was the 3000 watt hub motor but I have already spent a lot of money on the electric bike and so that will have to come later but from what I have read this one may do just fine.

I currently run a 6T hub motor with a 48V 20A battery pack in a GT bike frame I build a few years ago and really like the way the hub motor runs but would like more speed so I ordered a new Raptor 76r frame and plan on using leaf motor in that setup so my questions are as follows:

The frame has 150mm dropouts in the rear.
From the previous build I already have a premium 48V 20A rated up to 50A output lithium battery pack that I paid 900.00 to have built so I will have to base the new hub motor and brushless controller around this for now.

AT first I was just going to get the 26 inch 1500 watt 4T leaf hub motor kit but then read it was better to have these in the 17” or 19” motor rim for this frame

Do you offer the hub motor with the 150mm axle?

I want this to run at close 40mph / 60kph the 4T should do that but I also would like the upgraded controller over the standard. What is the best motor controller you offer with the 1500 watt motor?

I also noticed you had a 2000 watt motor in the motorcycle section. Is this hub motor available for the bicycle kit and what are the specs on it?

What controller does the 2000 watt motor use?

I am going to buy at least 2 of these. One in the next week +a bare spare and another in a month or so and then probably 2 or 3 after that. I have several friends that want a bike like mine so after I get mine done will be building theirs as well.

At the least I will order the standard 1500 watt hub motor kit in either the 26 or 24 or 20 rim and then I will just pick up a spare bare hub motor and lace the rim myself.

48V,1000W, 1500W rear hub motor for 20 inch or 24, 26, 27.5, 700c 28, 29inch

Posted by on December 30, 2021 Comments Off on 48V,1000W, 1500W rear hub motor for 20 inch or 24, 26, 27.5, 700c 28, 29inch

Do you have a more detailed drawing for dimensions of the 48V 1000W,1500W rear hub motor? I am particularly interested in the dimension I marked “A” so I can be sure the brake rotor disc will fit correctly.

The drawing from your web site shows the left side of the hub motor on the right side of the drawing. Also, in the video the hub motor is installed backwards and the rear derailleur is just hanging off the bike on the cable. Very confusing, but eventually I understood that the person who installed your hub motor on the bike put the motor in backwards, with the wire coming out the right side even though your specifications say the wire comes out the left side.

I suggest that you make all of your drawings, pictures, and video consistent left to right, because they are presently mixed up.

Here is an example of a drawing that is correct left versus right and has all the dimensions a bicycle builder needs to be confident the motor will fit the bicycle.

If I order with a free hub to use a cassette is the free hub body replaceable?

Does it look something like this?

Do you have a part number or a link for the replacement free hub and cassette for that motor?

Thank you very much for all the information, I really like this hub motor but I need to make sure it will fit and work well for my bike.

700c 48V 1500W rear hub motor – bike conversion kit

Posted by on December 29, 2021 Comments Off on 700c 48V 1500W rear hub motor – bike conversion kit

Q: 700c 48V 1500W front hub motor – bike conversion kit
Item ID #LBCK700C481500FN

Newest 700c 48V 1500W rear bike motor – conversion kit
Item ID #LBCK700C481500RN
What is the difference between these 2 bike conversion kits?
Can I get them with black spokes?
What is the winding (such as 12T, 8T, 6T, etc)?
Does it come with sprockets (rear cogs, or cassette)? If not, what kind do I order for it?
How much does it cost and how long does it take to ship to California, USA?

A: 1.They are the same motors.
LBCK700C481500FN is fit for 100mm rear dropout. Fit for front fork. Can’t use disk brake. ONLY use V brake on rim.
LBCK700C4815000RN can be installed sprocket on this motor. Fit for 135mm rear dropout. Fit for rear fork. Can install disk brake on rear motor. Also can use V brake on rim.

2. Black spokes ,, okay.. But it takes about 3 days to wait for this black spokes (Please leave message when you order)

3. Default: 5T. But we can make 6T, 8T … (Please leave message when you order)

4. LBCK700C481500FN can’t use sprocket.
LBCK7004815000RN can install sprocket. But Not come it. You can install yours on our hub motor. (Please leave message when you order rear cogs or cassette, then we can make motor as your sprocket. If No message, default: motor with screw thread for cogs

Q: You said:”3. Default: 5T. But we can make 6T, 8T … (Please leave message when you order)”
I have not read about an odd number such as 5T. Is this correct that your default is 5T?
Also, Do you have a right half twist throttle available for this instead of the right full twist?

A: Generally 700c 48V 1500W hub motor,use 5T.
If you leave message: 5T when you order (or send an email to us after paid) – It must 5T.
Yes. We also have other throttle. Please click below site. All throttles are fit for this bike conversion kit LBCK700C481500RN.

Also, leave message: what throttle. We will ship it instead of that full twist.

Motor controller with LCD-003 from Leaf Bike

Posted by on December 29, 2021 Comments Off on Motor controller with LCD-003 from Leaf Bike

48V 1000W-1500W-2000W, 36V 250W-500W-750W, 24V 250W Motor controllers with LCD-003 from Leaf Bike are used to drive 8-9-10-12-13-14-16-17-18-20-22-24-26-27.5-700C-28-29er inch hub motor bike wheels.

How to set max speed?
If you feel 20 inch or 24 inch,26 inch, 700c, 28 inch, 29 inch hub motor kit is too fast,please set it to be low speed.
* Press “sw/middle button” from LCD more than 2 seconds,then LCD will display.
* Press “up & down button” together more than 2 sconds until 72 is flashing ( 72 is kmh, if you hope works 20mph / 32kmh, press “down” to be 32)
* Press “sw/middle” button one time to save,then 24 is flashing.. (24 is hub motor wheel size. Don’t set)
* Press “sw/middle” button one time to save,then kmh or mph is flashing..
* Press “sw/middle” button one time to save,then press “sw/middle” button more than 2 seconds until be back.

Turn throttle,motor will work max speed as your setting.

—————
There is a “ 5 or 4 or 3 or 2 or 1 or 0” on the Left side of LCD.
* Be “0” – throttle & pedal assist NOT work.
* Be “1” – throttle works (If install pedal assist, pedal about 3 circels,then can drive motor to work)
* Be “2” – throttle works (If install pedal assist, pedal about 2.5 circels,then can drive motor to work)
* Be “3” – throttle works (If install pedal assist, pedal about 2 circels,then can drive motor to work)
* Be “4” – throttle works (If install pedal assist, pedal about 1.5 circels,then can drive motor to work)
* Be “5” – throttle works (If install pedal assist, pedal about 1 circels,then can drive motor to work)

If NOT install that pedal assist,ONLY use throttle to drive motor. But Should be 1 or 2 or 3 or 4 or 5.(Be 0,turn off throttle)

——————————–
How to use three button switch?
1.We cut off that blue wire.It’s for reverse. If reconnect this blue wire.
This yellow button be left / middle,29 inch bike motor kit works forward. Be right side,hub motor works bacwkard / reverse…

2.Green button is used to control cruise, while electric bike motor is running,also over some speed,example: over 1/3 max speed,at this time,press green button one time,then loose throttle,LCD display “C”,motor will works the same speed. Re-press this green button one time or press brake lever or turn throttle to max, electric bike motor will stop.

3.Red button be up,regen on. Be down,regen off. This regen is not strong.Only while braking with a little regen.