Category Archives: hub motor - Page 20

electric bike hub motor

Posted by on January 26, 2022 Comments Off on electric bike hub motor

Hub motor is an electric bike motor that is an important part for electric bike.A common bicycle with a motorized wheel(hub motor) is an electric bicycle.

1.According as your size of rim,it has 6″ 8″ 10″ 12″ 14″ 16″ 18″ casting hub motors and 20″ 24″ 26″ 700c and 28″ electric bike hub motors
From 6″ to 18″,the rims are much smaller,so always casting hub.And used for electric scooters,electric tricycles,sometimes also used for folding electric bicycles.
From 20″ to 28″,because of rims are much bigger,always use spokes to fit.And used for electric bicycles.

2.According as whether has “brush”,it has two type:brushless hub motor and brushed hub motor
Brushless hub motor is make up of aluminium hub,aluminium covers,axis,bearings,copper winding, rotor,hall sensor..
Brushed hub motor is make up of aluminium hub,aluminium covers,axis,bearings,gear box(several gears inside),printed copper slice,two pcs of brushes..

The brushless hub motor’s principle:electromagnetic fields are supplied to the stationary copper windings of the motor. The hub(outer part of the motor)follows, turning the attached wheel.

The brushed hub motor’s principle:energy is transferred by brushes contacting the rotating shaft of the motor that drive gears,then drive hub.

Compare them:
Noise Efficiency Torque Use-life
1.brushless hub motor: √ >78% √ >3-Year
2.brushed hub motor: a little noise <70% a little larger replace "brush" in 2 year With the advantage of brushless hub motor,it used for electric bike widely. According as use,it also called electric bike motor. According as current,it has ac and dc hub motor.But nearly all of hub motors are direct current(DC).

How to replace li battery cells?

Posted by on January 25, 2022 Comments Off on How to replace li battery cells?

Lead acid,LiFePo4,LiMn2O4,any kind of battery has use life.Generally 1 year warranty for battery.

Battery is a special good that is different from brushless controller,hub motor.Why?Controller and motor,if you don’t use for 1 year.Still no problem.But battery,you should charge it each two weeks,even if you don’t use.

For lithium battery,there are many cells make up of one battery.
Below we talk about LiMn2O4 battery first.
Now 4.2V 4Ah LiMn2O4 cell is familiar with us.
7 series for 24V,10 series for 36V,13 series for 48V
1.1 set of 24V 16Ah LiMn2O4 needs 28 pcs cells;
2.1 set of 36V 12Ah LiMn2O4 needs 30 pcs cells;
3.1 set of 36V 16Ah LiMn2O4 needs 40 pcs cells;
4.1 set of 48V 12Ah LiMn2O4 needs 39 pcs cells.

Too many cells for one battery,only one cell is sick.The whole of battery will be broken.
You will find that,full chargerd your battery,but it only drive your bicycle several meters,the motor will stop.
Because BMS found one sick cell,in order to protect other cells.BMS turns off power.

Now you need to replace sick cell,pls test as below,you will find it.
It’s a 36V li-ion battery.
Remove the battery end cover containing the charger socket. You will find a printed circuit board (PCB).
It is a battery management system (BMS) which equalizes the charge in each of the cells.
The wire B1 is the one attached to the battery anode. Connecting his professional quality voltmeter to the battery anode and to the other nine wires in succession.

There is one 10-Pin connector on this PCB. (B10 B9 B8 B7 B6 B5 B4 B3 B2 B1)

Measure the voltage between
the green wire and other nine wires as below:

B1 green wire to: Specification
B2 yellow wire(the second wire) 3.6V ~ 4.15V
B3 yellow wire(the third wire) 7.2V ~ 8.30V
B4 yellow wire(the fourth wire) 10.8V ~ 12.45V
B5 yellow wire(the fifth wire) 14.4V ~ 16.60V
B6 yellow wire(the sixth wire) 18.0V ~ 20.75V
B7 yellow wire(the seventh wire) 21.6V ~ 24.90V
B8 yellow wire(the eighth wire) 25.2V ~ 29.05V
B9 yellow wire(the ninth wire) 28.8V ~ 33.20V
B10 black wire (the tenth wire) 32.4V ~ 37.35V
If the voltages are normal,all cells are okay.

Incidentally, 32.4V~37.35V + 3.6V~4.15V = 36V~41.5V

Then, measure voltage of the battery
without BMS (B- and battery anode) 36V~41.5V
with BMS (D- and battery anode) 36V~41.5V
If these two voltages are the same, then the battery pack is okay.

Note:If the voltage of any cell is more than 4.2V.I think the cell is overcharge.It can stop BMS and battery work.So you should find out which cell is over charged.

Hub motor for electric bike

Posted by on January 25, 2022 Comments Off on Hub motor for electric bike

Hub motor is an electric motor that is an important part for electric bike.A common bicycle with a motorized wheel(hub motor) is an electric bicycle.

1.According as your size of rim,it has 6″ 8″ 10″ 12″ 14″ 16″ 18″ casting hub motors and 20″ 24″ 26″ 700c and 28″ electric bike hub motors
From 6″ to 18″,the rims are much smaller,so always casting hub.And used for electric scooters,electric tricycles,sometimes also used for folding electric bicycles.
From 20″ to 28″,because of rims are much bigger,always use spokes to fit.And used for electric bicycles.

2.According as whether has “brush”,it has two types:brushless hub motor and brushed hub motor
Brushless hub motor is make up of aluminium hub,aluminium covers,axis,bearings,copper winding, rotor,hall sensor..
Brushed hub motor is make up of aluminium hub,aluminium covers,axis,bearings,gear box(several gears inside),printed copper slice,two pcs of brushes..

The brushless hub motor’s principle:electromagnetic fields are supplied to the stationary copper windings of the motor. The hub(outer part of the motor)follows, turning the attached wheel.

The brushed hub motor’s principle:energy is transferred by brushes contacting the rotating shaft of the motor that drive gears,then drive hub.

With the advantage of brushless hub motor,it used for electric bike widely.

According as use,it also called electric bike hub motor.
According as current,it has ac and dc hub motor.But nearly all of hub motors are direct current(DC).

electric hub motor for e-motorcycle

Posted by on January 25, 2022 Comments Off on electric hub motor for e-motorcycle

Motorcycle is fast,exciting.

Traditional motorcycles use gasoline and newer versions like the run on electricity. When start,should swap shift from NO.1 to NO.5.It takes more than 10s to reach 80m/h and makes a lot of noise.
Use leafmotor’s blw-16b electric hub motor.Reach 80m/h,it just take 5s without any noise.

This hub motor is make up of aluminium hub,cover,magnet,rotor, winding,axis etc.The net weight is about 13.5kg,use 16×2.5″tyre,load approximate 500lb.Motor speed,we can customize according as your actually need.

Gasoline engine need to replace machine oil termly,but this electric hub motor doesn’t need to service.

Calculate cost as 30 miles per day
1.Replace machine oil each month,12 times per year.The price for each bottle of machine oil is $20USD. 30 miles per day use 0.5 gallon,it costs $2USD/day.Total price:$970USD/year,$1940USD/two years.
2.Use electric motorcycle,charge battery everyday cost $0.2USD/per day.Total price:$73USD/year,$146USD/two year.

Two years later,replace 1 pcs of new 48V or 72V lead-acid battery,it costs less than $500USD.
Choose electric hub motor for your motorcycle,it save $647USD/per year.

In order to have a good environment,please ride e-motorcycle.

14 inch electric hub motor for e-scooter

Posted by on January 15, 2022 Comments Off on 14 inch electric hub motor for e-scooter

36V 750W / 48V 1000W 14 inch brushless gearless hub motor is make up of aluminium hub,aluminium cover,magnet,rotor,winding,axis etc.Mounted 14×2 1/4~2 1/2″tyre,load approximate 300lb. Hub Motor speed,we can customize according as your actually need.
It’s used for electric bike,electric scooter,tricycle.

More info about this hub motor
1.The drawings of HBL-14″ rear hub motor,it’s fit for standard 135mm rear fork.
Net weight:6.86kgs

2.The drawings of HBL-14″ front hub motor,it’s fit for standard 100mm front fork.
Net weight:6.58kgs

14″ e-bike stopped and waited for a moment

Posted by on January 15, 2022 Comments Off on 14″ e-bike stopped and waited for a moment

Q:Ride ebike on the flat road,no problem,but when I climb the hill,it will stop and wait for a moment,it still can re-start and have the same problem at once.

A:The temp inside the controller is too high and in order to protect this controller,should wait for a moment until the temp is lower than protective temp.

Solve:Use more MOS-FET brushless controller.

Now our 48V brushless motor controller has 15-MOSFET.More MOSFET afford temp and the temp rise very slow.It can solve this problem.

In market,always use 9-MOSFET to drive 48V 1000W hub motor.This kind of brushless controller is easy to be broken because of high temp will break MOSFET.

36V 750W / 48V 1000W 14″ brushless gearless hub motor is make up of aluminium hub,aluminium cover,magnet,rotor,winding,axis etc.Mounted 14×2 1/4~2 1/2″tyre,load approximate 300lb.Motor speed,we can customize according as your actually need.
It’s used for e-bike,e-scooter.

How to make hub motor reverse

Posted by on January 15, 2022 Comments Off on How to make hub motor reverse

Q:Received my DIY e-bike kit,18″ front wheel 48V 1000W hub motor with brushless motor controller,done installed on tricycle,test system,load 300pl on motor that still had enough power.
But one issue:I want to make tricycle reverse,help…

A:Please find a 2-pin connector(purple and black wires) from controller and jump these two wires,also can use a ON/OFF switch to control it.

BTW,connect wires according as below connecting.Make a sample:
1.Forward.
Motor ——– Controller
Thick yellow wire ——– Thick yellow wire
Thick green wire ——– Thick green wire
Thick blue wire ——– Thick blue wire

Motor hall ——– Controller hall
Thin yellow wire ——– Thin yellow wire
Thin green wire ——– Thin green wire
Thin blue wire ——– Thin blue wire
Thin red wire ——– Thin red wire
Thin black wire ——– Thin black wire

2.Reverse.
Exchange thick yellow and green wires and thin green and blue wires can make system backward.
Motor ——– Controller
Thick yellow wire ——- Thick green wire
Thick green wire ——- Thick yellow wire
Thick blue wire ——– Thick blue wire

Motor hall ——– Controller hall
Thin yellow wire ——– Thin yellow wire
Thin green wire ——– Thin blue wire
Thin blue wire ——– Thin green wire
Thin red wire ——– Thin red wire
Thin black wire ——– Thin black wire

Strange noise from hub motor

Posted by on January 15, 2022 Comments Off on Strange noise from hub motor

Q: The hub motor makes a noise once every turn and it gets stuck (or at least much more friction) at the same angle. It feels like it could be some magnetic effect but more likely it´s some mechanical contact that´s disturbing the rotation.

A: The noise comes from some metal impurity on the magnet.

Solve: Disconnect hub and remove it

Other answer 1.
Take rotor out of the magnet hub isn’t easy.Be careful your hands.Need two guys to do this.One guy press the hub,the other draws the rotor.

Other answer 2.
No other way to solve it,except disconnect hub motor.
Do it as the instruction.Be careful.

Other answer 3.
Magnet is easy to magnetize metal matter.Assembly hub motors should have a clean work environment.

Other answer 4.
There is no any room between rotor and magnet.See picture.Metal scrap may be inside the winding.Test motor before shipment,I think can’t find this problem.But after long distance to ship,it will be magnetized by magnet.

Other answer 5.
Small problem,it’s easy to repair.I disconnected two hub motors,one is old motor,the other is new one,and exchanged the rotor to different hub.That changed motor’s performance. Interesting job.I think you will like to repair it.

How to disconnect hub motor?
Disconnect it as below:

Request of info about your hub motors

Posted by on January 15, 2022 Comments Off on Request of info about your hub motors

Q:I’m planning to start a small production of electric vehicles and I’m evaluating your products.
I would like you to clarify the following details:
1) I read the performance data of HBL motor 24V/300W-36V/750W-48V/1000W, are these data referring to the same physical motor ?
2) What are the physical differencies between HBL-36F1 / HBL-36F2 / HBL-48F ? I noticed that the weight is the same, is the gauge of the coil wires and/or the turns number of the coils different for each motor ?
3) Are HBL motors equipped with internal position sensors ?
4) Besides 14/16/18″ can you supply also 20″ aluminium casted rims for HBL motors ?

A:Thank you for you are interested in our electric bike motor.You are very professional.
About the first and the second question,you are right,these performance datas come from the same motor.No difference.
About the third question,HBL is brushless gearless motor with internal hall sensor.
About the fourth question,in past we had this 20″ aluminium casted rims for HBL motors.
Now no body use this 20″ hub motor,so we don’t manufacture this kind of motor.
HBL-36F1/HBL-F2/HBL-48F these three kinds of motor,if they have differences that come from the gauge of the coil wires and/or the turns number of the coils.

BTW,if you hope get other performance about this hub motor,for example:faster,slower,more power at the highest efficiency point.We can customize according as your order.

No differences between hub motor and electric bike motor

Posted by on January 15, 2022 Comments Off on No differences between hub motor and electric bike motor

Q:You wrote me that there are no differences between HBL-36F1/HBL-F2/HBL-48F hub motor, so the different prices listed on your website are just for commercial reasons ?
I’m glad to hear you can supply customized products, is this possible even for small numbers ? (We are starting this type of business and at the beginning we will need just a few pieces).
I really appreciate your hub motors mainly for the technical
specifications provided rarely present for this type of product.
I would be interested in testing the following electric bike motor:
– HBM-Rear (diam.=145mm)
– HBL-Rear (diam.=243mm)
(No rims, no spokes, no custom products at this time)
However I would like to know if disc brakes can be mounted on these
motors and, as I have to make some particular tests, if you can supply both motors with a 12 (or 14) tooth fixed sprocket mounted on (I mean just a single fixed sprocket, not the classic freewheel gear).
A:Our HBM-Rear and HBL-Rear can both be installed disc brake and freewheel are fit for standard 135mm rear fork.
Please review picture”Disk-6in”.Does your Disk brake with this threaded adapter?If have,your disc brake can mounted on our motor.
If you this disc brake doesn’t have this threaded adapter,we will offer you this part.