The brushless motor was nearly put into operation, the factory has been injected into the GB/T5903 in the L-CKC100 ~ L-CKC220 in extreme pressure industrial gear oil in the 200 to 300 hours after the operation, should be first
First oil change in the future use of the quality of the oil should be checked regularly for deterioration of the oil mixed with impurities or be replaced.
In general, for long continuous work from the reducer, according to 5000 hours or once a year to run the new oil replacement, long-term out of brushless hub motor, re-operation should be replaced before.
Gear oil should be added to the same oil with the original grade shall not be mixed with different grades of oil used, the same as the viscosity of different grades of oil allowed to mix.
Oil should wait for the gear to cool down without risk of burning up, but should remain warm, because the completely cooled, oil viscosity, oil discharge difficult.
Maintenance for Brushless Motor
AC induction BLDC motor
Today’s domestic industrial control industry, for motors usually have such a view: low-end motor using AC induction BLDC motor, high-end motor servo motor. In fact there is a domestic motor applications skip the phenomenon, from the AC induction motor to jump directly to the BLDC motor controller, and the middle of the brushless DC motor is often ignored by people. Brushless DC motor as a DC brush motor characteristics, but also the frequency of the device, they are called the DC inverter, the international generic term for the BLDC. Unique brushless DC motor of high efficiency, low fever and other features and advantages, are in line with the national energy saving requirements. By comparison with some other motor, we can see these features more intuitive, and thus facilitate the selection of the motor when engineers select the most suitable motor, not the most expensive motor.
700c 48V 52V 1000W rear bike conversion kit electric hub motor wheel video
The 700c bike conversion kit combines the full E-bike technology: direct drive Brushless Gearless high torque hub motor to change almost every bicycle into a personal electric bike. Save energy, protect environment and save money with a lot of fun. Saving 10% of electricity, Improve the efficiency of 8% With The Newest Materials Steel Rotor.
This 700c bike motor kit works with a 48V or 52V battery.
Main Features:
>. Rim: 700c / 622 double wall Alloy (Rim Fit For: 700 x 18C / 20C / 23C / 25C / 28C / 32C / 35C / 40C)
>. Spoke: 12 gauge / 184mm Length x 36 pcs
>. Default: Black spokes
>. Optional: Silver spokes — Please leave message.
>. Engine: Bldc hub motor
>>. Voltage: 48V / 52V
>>. Power: 1000W
>>. Efficiency: 90.5%
>>. Max speed: 84.5 kmh — 52.5 mph Default (Optional other speed: 35mph or 25mph,15mph..please leave message)
>>. Mechanical brake: Disc or V
>>. Sprocket: Freewheel or Cassette
>>. Cable location: shaft end, Left
>>. Cable length: 100cm / 40″
>>. Install: spacing of 135mm (6 speed) ~ 155mm fork
>>. Noise: < 60 db
>>. Surface: Black painted
>. Driver: brushless controller
>>. With LCD: YES
>>. Rated Voltage: DC 48 / 52 Volts
>>. Min. Voltage: DC 40 ± 0.5 V
>>. Rated power: 1000 Watts
>>. Casing material: aluminum
>>. Maximum Current: 26 A ± 1 Amps
>>. Thermal: aluminum shell and the substrate
>>. 3 phase 120° brushless motor
>>. Operating Conditions: -20~45 °C
>>. Waterproof design
>>. Size: 105 mm L x 72 mm W x 38 mm H
With LCD, More Function:
* Cruise – Yes
* Forward & Backwards (Optional: On / Off)
* Kmh & mph (Optional)
* Speeds ( 0 – 5 ) – “0” is off throttle. “1” is the slowest. “5” is the fastest.
* Battery gauge
* ..
Package Content:
1 x 700c 48V 52V 1000W rear hub motor wheel
1 x 48V 52V 1000W 12-MOSFET motor controller
1 x LCD
1 x Twist throttle — Cable length: 1500mm
1 x Brake levers — Cable length: 1500mm
1 x Three button switches ( control cruise.. ) — Cable length: 1500mm
1 x Pedal assist — Cable length: 900mm
27 inch 48V 52V 1000W electric bike conversion kit front hub motor wheel video
The 27 inch bike kit combines the full E-bike technology: direct drive Brushless Gearless high torque hub Motor to change almost every bicycle into a personal electric bike. Save energy, protect environment and save money with a lot of fun. Saving 10% of electricity, Improve the efficiency of 8% With The Newest Materials Steel Rotor.
This 27 inch bike conversion kit works with a 48V or 52V battery.
Main Features:
>. Rim: 27 inch double wall Alloy (Rim Fit For: 27 x 1-1/4, 1-3/8 tire)
>. Spoke: 12 gauge / 198mm Length x 36 pcs
>. Default: Silver spokes
>. Optional: Black spokes — Please leave message.
>. Engine: Bldc hub motor
>>. Voltage: 48V / 52V
>>. Power: 1000W
>>. Efficiency: 90.5%
>>. Max speed: 86.1 kmh — 53.5 mph Default (Optional other speed: 35mph or 25mph,15mph..)
>>. Mechanical brake: Disk or V
>>. Cable location: shaft end, LEFT
>>. Cable length: 150cm / 60″
>>. Install: spacing of 100mm fork
>>. Noise: < 60 db
>>. Surface: Black painted
>. Driver: brushless controller
>>. MOSFET: 12 PCS
>>. With LCD: YES
>>. Rated Voltage: DC 48 / 52 Volts
>>. Min. Voltage: DC 40 ± 0.5 V
>>. Rated power: 1000 Watts
>>. Casing material: aluminium
>>. Maximum Current: 26 A ± 1 Amps
>>. Thermal: aluminum shell and the substrate
>>. 3 phase 120° brushless motor
>>. Operating Conditions: -20~45 °C
>>. Waterproof design
>>. Size: 105 mm L x 72 mm W x 38 mm H
With LCD, More Function:
* Cruise
* Forward & Backward (Optional)
* Kmh & mph (Optional)
* Speeds ( 0 – 5 ) “0” is off. “1” is the slowest. “5” is the fastest.
* Battery gauge
* ..
Package Content:
1 x 27 inch 48V 52V 1000W front hub motor wheel
1 x 48V 52V 1000W 12-MOSFET motor controller
1 x LCD
1 x Twist throttle — Cable length: 1500mm
1 x Brake levers — Cable length: 1500mm
1 x Three button switches ( control cruise.. ) — Cable length: 1500mm
1 x Pedal assist — Cable length: 900mm
Net Weight: 11 kg
Package Size: 68cm L x 68cm W x 25cm H
Package Type: Cardboard Box
28 inch 48V 52V 1000W rear hub motor wheel electric bike conversion kit
The 28 inch bike kit combines the full E-bike technology: direct drive Brushless Gearless high torque Bike Motor to change almost every bicycle into a personal electric bike. Save energy, protect environment and save money with a lot of fun.
This 28 inch bike conversion kit can work with a 48V or 52V battery.
Main Features:
>. Rim: 28 inch double wall Alloy (Rim Fit For: 28 x 1 5/8″ tire)
>. Spoke: 12 gauge / 184mm Length x 36 pcs
>. Default: Black spokes
>. Optional: Silver spokes — Please leave message.
>. Engine: Bldc hub motor
>>. Voltage: 48V / 52V
>>. Power: 1000W
>>. Efficiency: 90.5%
>>. Max speed: 87.8 kmh — 54.6 mph Default (Optional other speed: 35mph or 25mph,15mph..please leave message)
>>. Mechanical brake: Disc or V
>>. Sprocket: Freewheel or Cassette
>>. Cable location: shaft end, Left
>>. Cable length: 100cm / 40″
>>. Install: spacing of 135mm (6 speed) ~ 155mm(9 speed) fork
>>. Noise: < 60 db
>>. Surface: Black painted
>. Driver: brushless controller
>>. MOSFET: 12 PCS
>>. With LCD: YES
>>. Rated Voltage: DC 48 / 52 Volts
>>. Min. Voltage: DC 40 ± 0.5 V
>>. Rated power: 1000 Watts
>>. Casing material: aluminium
>>. Maximum Current: 26 A ± 1 Amps
>>. Thermal: aluminum shell and the substrate
>>. 3 phase 120° brushless motor
>>. Operating Conditions: -20~45 °C
>>. Waterproof design
>>. Size: 105 mm L x 72 mm W x 38 mm H
With LCD, More Function:
* Cruise – Yes
* Forward & Backward (Optional)
* Kmh & mph (Optional)
* Speeds ( 0 – 5 ) – “0” is off throttle. “1” is the slowest ~ “5” is the fastest.
* Battery gauge
* ..
Package Content:
1 x 28 inch 48V 52V 1000W rear hub motor wheel
1 x 48V 52V 1000W 12-MOSFET motor controller
1 x LCD
1 x Twist throttle — Cable length: 1500mm (Optional: thumb throttle)
1 x Brake levers — Cable length: 1500mm
1 x Three button switches ( control cruise.. ) — Cable length: 1500mm
1 x Pedal assist — Cable length: 900mm
Net Weight: 11.2 kg / 24.6 lbs
Package Size: 66cm L x 66cm W x 25cm H
Package Type: Cardboard Box
29 inch 48V 1000W rear hub motor wheel electric bike conversion kit video
The 29 inch bike kit combines the full E-bike technology: direct drive Brushless Gearless high torque hub Motor to change almost every bicycle into a personal electric bike. Save energy, protect environment and save money with a lot of fun. Saving 10% of electricity, Improve the efficiency of 8% With The Newest Materials Steel Rotor.
This 29 inch bike conversion kit works with a 48V battery.
Main Features:
>. Rim: 29 inch double wall Alloy (Rim Fit For: 29 x 1.95″ ~ 2.5″ tire)
>. Spoke: Silver 12 gauge / 188mm Length x 36 pcs
>. Default: Silver spokes
>. Optional: Black spokes — Please leave message.
>. Engine: Bldc electric hub motor
>>. Voltage: 48V
>>. Power: 1000W
>>. Efficiency: 90.5%
>>. Max speed: 72.4 kmh — 44.9 mph Default (Free customization other speeds: 35mph or 30mph, 25mph, 20mph, 15mph..please leave message)
>>. Mechanical brake: Disc or V
>>. Freewheel / Cassette: space for single speed..6 speed or 7 speed
>>. Cable location: shaft end, LEFT
>>. Cable length: 100cm / 40″
>>. Install: spacing of 135mm fork (max 6 speed) ~ 155mm fork (max 9 speed)
>>. Noise: < 60 db
>>. Surface: Black painted
>. Driver: Brushless motor controller
Default: Heat Shrink Bullet Crimp Female Male Wire Connectors Electrical Terminals for battery plug.(Leave message Optional: XT-60)
>>. MOSFET: 12 PCS
>>. With LCD: YES
>>. Rated Voltage: DC 48 Volts
>>. Min. Voltage: DC 40 ± 0.5 V
>>. Rated power: 1000 Watts
>>. Casing material: aluminum
>>. Maximum Current: 26 A ± 1 Amps
>>. Thermal: aluminum shell and the substrate
>>. 3 phase 120° brushless motor
>>. Operating Conditions: -20~45 °C
>>. Waterproof design
>>. Size: 171 mm L x 82 mm W x 42mm H
With LCD, More Function:
* Cruise — Green switch to control
* Kmh & mph (Optional)
* Max speed ( 0 ~ 72 kmh )
* Pedal assist ( 0 – 5 )
* Battery gauge
* ..
Package Content:
1 x 29 inch 48V 1000W rear hub motor wheel
1 x 48V 1000W 12-MOSFET motor controller
1 x LCD
1 x Twist throttle — Cable length: 1500mm
1 x Brake levers — Cable length: 1500mm
1 x Three button switches ( control cruise.. ) — Cable length: 1500mm
1 x Pedal assist — Cable length: 900mm
Net Weight: 11.2 kg
Package Size: 66cm L x 66cm W x 25cm H
Package Type: Cardboard Box
Chinese bike conversion kit
Leaf motor engines are now the references upscale market on the Chinese bike conversion kit.
Tristar has to choose the best for these bike conversion kits and assembly solutions to practical, simple and scalable (System Evolution Plug’n’play).
These components are installed to the card used to design and build a custom electric bike conversion kit by choosing the bike and the engine … or vice versa!
U.S. cruisers, bike carriers Yuba, scooters, recumbent bikes, all can be motorized and mountain bikes, hybrid bikes, folding bikes and city bikes. We can offer specific configurations to your needs or desires, or develop a new you.
Count from 950 € (without installation) for a kit front or rear wheel motor (or FH154 vicky 3), 250W electronic box, sensor pedaling 37V10Ah LiPo battery integrated into a luggage rack bag and charger.
Allow between € 1100 and € 1300 “with a ladle” for a rear engine four or Vicky RH205 in SPh and Controller 48V 20A, 27A or 30A of about 500W to 1000W nominal (800W to 1500W in crete!)
Ca Décoiffe severe! Total ban on public roads, of course, some insurers ‘militants’ admit nevertheless well known that such a device (up to 600W nominal) is much more reasonable that Porsche in the hands of a bad driver, and take responsibility to provide comprehensive insurance (equivalent moped) for this type of gear.
Each of the decision to go with it responsibilities that go with it, headphone highly recommended, as well as hydraulic disc brakes and one for the best full suspension bike.
An ideal candidate, the DH bike (down hill)
Oversized bike which is what is more sturdy and safe, a pair of tires and one large city well is safe.
Ideal conditions-yourself kit if you have good mechanical knowledge, if not bring them up by competent persons, even when we speak of power and speed quite “removed” on machines weighing 20/25Kg once powered and functioning very reactive!
Between these two kits type, a lot of solutions very consistent on a daily basis for cargo bikes, ATVs punchy, efficient city bikes, scooters, scooters ….
Contact us for any project is, we will discuss with you and offer you a custom quote and / or advice in this area.
We remind you that our workshop is at your service.
domestic representative bike conversion kit
This paper describes some domestic representative bike conversion kit the whole circuit, and point out the difference between other products and their characteristics. Listed in the circuit are derived based on physical mapping, map scale component by the author. Through the presentation of specific examples, the purpose of replication.
bike conversion kit
Popular electric bicycles, electric motorcycles most use DC motors, DC motor speed controller for many species. Electric vehicle controller core is the pulse-width modulation (PWM) device, and a sound controller, also has a battery voltage protection, motor overcurrent protection, power brakes, power display.
The size of the controller to power electric vehicles can be divided into high, medium power, low-power categories. Electric bikes use a low-power, cargo tricycle, and electric motors to be used in power and high power. With the motor from the sub, can be divided into brush, brushless two categories. About brushless controller, subject to current technology and cost constraints, the failure rate is higher. I believe that the brushless controller maintenance should be the main manufacturers. The applications have more brush control, is able to use similar controllers for direct substitution or maintenance.
Bike Conversion Kit – Electric drive system for bicycles
Bike Conversion Kit – Electric drive system for bicycles.
Our system is designed for 90% of the bicycle rim 26.
It’s pretty simple to install and requires no electrical connections making it everything is connected.
It only takes a couple of tools to assemble the grill, engine, accelerator and brake levers.
Once done, place the batteries, and enjoy a high performance electric vehicles, fast, quiet and economical.
To install the battery holder grill, it is necessary that the frame of the bike has: 1) Holes on the rear axle to mount traditional grill. These perforations with internal thread, allow istalacion bolts that anchor the grid carries batteries in its foothold principal.2) Support for V Brake rear brakes. There are installed brackets that hold the second support grid baterias.La carries most of the bikes that are in the market have these features. Now, if you have no rear brake Brake V, it is still possible to hold the grill to the frame using clamps.
Turn your conventional bike into “electrical” pedal-assisted electric equipment
Turn your conventional bike into “electrical” pedal-assisted electric equipment of high quality and well made long journeys with much less effort and while exercising.
Electric bike conversion kit composed of high quality 250W wheelers (not including the tire), Lithium Battery with BMS (Battery Management System), pedal sensor, selector switch on the level of assistance, wiring and battery charger.
The bike conversion kit Bereco applies almost 100% of the bikes on the market, provided that the distance between forks is 100mm, which is the more standard implemented worldwide. Likewise, the kit is available in various wheel sizes from 20 inches to 700 C, through 22, 24 and 26 inches.
According to the Bereco Bike Kit versions with the help can provide a range of between 50 and 100 km, always depending on usage conditions and terrain, so you can plan trips that were previously impossible by distance.
SPECIFICATIONS:
Motor: 250 W, Front Wheel
Wheel Diameter: 20, 22, 24, 26 inches and 700 C
Pedal Assistance: 2 Levels
Battery: 36 V/10 Ah Lifepo4 of
Battery Life: 2,000 cycles
Autonomy *: 90/100 miles at full load